检测到您已登录华为云国际站账号,为了您更好的体验,建议您访问国际站服务网站 https://www.huaweicloud.com/intl/zh-cn
不再显示此消息
Assume that the subnets of the data center are 192.168.3.0/24 and 192.168.4.0/24, the subnets of the VPC are 192.168.1.0/24 and 192.168.2.0/24, and the public IP address of the IPsec tunnel egress in the VPC is 1.1.1.1, which can be obtained from the local gateway parameters of the
Example response { "connection_monitor": { "id": "76f64229-demo-a8df-va86-3907e2815b6d", "status": "ACTIVE", "vpn_connection_id": "cae286f2-demo-a8df-va86-e22416ca1220", "type": "gateway", "source_ip": "88.***.***.60", "destination_ip
Bandwidth: You are charged for the outbound bandwidth, that is, bandwidth for traffic sent from a VPC on the cloud to a customer gateway in your on-premises data center. If the purchased bandwidth is 10 Mbit/s or less, the inbound bandwidth is limited to 10 Mbit/s.
In the VPN connection list, dual connections to the same customer gateway are identified by . If such dual connections are displayed on different pages, and are also displayed on different pages.
Table 1 Version requirements Debian Version OpenSSL Version OpenVPN Version 12.0.0 1.1.1 2.5 or later High-Risk Operation Warning Before configuring a client, exercise caution when adding, deleting, or modifying the local subnet of a VPN gateway and the customer subnet or policy configuration
and Usage Guidance for the Internet Key Exchange Protocol Version 2 (IKEv2) RFC 3947: Negotiation of NAT-Traversal in the IKE RFC 3948: UDP Encapsulation of IPsec ESP Packets RFC 3706: A Traffic-Based Method of Detecting Dead Internet Key Exchange (IKE) Peers RFC 4271: A Border Gateway
On Ubuntu, run the following command to go to the directory where the client configuration file is stored: cd /opt/ Run the following command to start the OpenVPN client and connect to the VPN gateway: openvpn --config /opt/openvpn_config_user-01.conf If the following information
a VPN connection in static routing mode for a VPN gateway associated with a VPC.
The value cannot be the gateway IP address of the client CIDR block. For example, if the client CIDR block is 192.168.0.0/24, 192.168.0.1 cannot be configured as a client address. The value must be the first host address in a CIDR block with a 30-bit mask.
The value cannot be the gateway IP address of the client CIDR block. For example, if the client CIDR block is 192.168.0.0/24, 192.168.0.1 cannot be configured as a client address. The value must be the first host address in a CIDR block with a 30-bit mask.
The value cannot be the gateway IP address of the client CIDR block. For example, if the client CIDR block is 192.168.0.0/24, 192.168.0.1 cannot be configured as a client address. The value must be the first host address in a CIDR block with a 30-bit mask.
Run the following command to go to the directory where the client configuration file is stored: cd /opt/ Run the following command to start the OpenVPN client and connect to the VPN gateway: openvpn --config /opt/openvpn_config_user-01.conf If the following information in bold is
On openSUSE, run the following command to go to the directory where the client configuration file is stored: cd /opt/ Run the following command to start the OpenVPN client and connect to the VPN gateway: openvpn --config /opt/openvpn_config_user-01.conf If the following information
-----BEGIN CERTIFICATE-----******-----END CERTIFICATE----- Table 2 Key parameters in a request for creating a VPN server in password authentication mode Parameter Description Example Value p2c_vgw_id Specifies the ID of the P2C VPN gateway that has been created. dea8c4fb-be5c-4d50
On CentOS, run the following command to go to the directory where the client configuration file is stored: cd /opt/ Run the following command to start the OpenVPN client and connect to the VPN gateway: openvpn --config /opt/openvpn_config_user-01.conf If the following information